Plastic Pipes Conference Association # 2021 Amsterdam
Alireza Sahaf Amin, Dr. Gholamreza Pircheraghi
PE-Xa pipes used in the hot water supply are required for high mechanical strength and high creep resistance at high temperature. Because of the higher cross-link degree of PE-Xa pipes as compared with other crosslinked pipes methods , these pipes which are made by peroxide crosslinking have better performance in the hot water application. It has long been recognized that stabilization of such highly cross-linked polymers by commercial antioxidants (AO) faces many challenges including the possible interference of the AOs with the crosslinking step. In this paper, the PE-Xa pipes which mixed with several stabilizers were tested to evaluate the effect on cross-link degree and the oxygen induction time, as a result, it was found that the combination of AOs for PE-Xa pipes plays an important role to prolong the OIT without inhibiting the cross-linking. Another issue is to check the possibilities on how to measure the gel content more quickly and if there is a correlation with gel content. In this paper, we check this issue and try to prepare some conclusions.
Related papers
Author(s) : Ajay Taraiya, Peter Degenhart, Mark Boerakker
In PPXX, a technology was presented for the first time that could bi-axially orient polyolefin pipes. With this technology, it is possible to prepare pipes that have a performance far beyond the standard ones. One approach to achieving this performance is via a continuous in-line process. To optimize the in-line...
Author(s) : Olivera Bilic, Vivek Rohatgi, Brody Peterson, David Hukill
Demand for conduit pipe is expected to surge globally due to rapid industrialization and urbanization in residential and commercial sectors. Just in the U.S., according to Market Research analysis, expected growth of the plastic conduit pipe market is at a CAGR of more than 5% over the next ten years. In response to...
Author(s) : Yi Zhong, Qianshi Ma, Haihua Yu
BSTRACT The residential district adopts central heating for low temperature radiators system. Due to the disrepair of the secondary heating pipe network that pipe from heat exchange station to user entrance, the running, leaking, dripping and leakage are serious, and the accidents occur frequently. The heat...
Author(s) : Ricardo Pascual
Social awareness with aspects related to the conservation of the environment and sustainability, the acceptance by citizens of the need to reduce consumption, reuse products, repair as far as possible and, fundamentally, the action of recycling at the end of its life, facilitates the availability of recycled plastics...
Author(s) : Amster Howard
This paper explores the use of a composite soil stiffness as a valuable design tool to consider when a pipeline traverses through poor soil conditions. Thermoplastic pipe are flexible pipe and require good soil support at the sides of the pipe to minimize deflection. However, sometimes the trench walls are weak soils...
Author(s) : James F. Mason, Akshay Ponda, Hermann van Laak, Tobias Bauer
The long-term strength of unplasticized polyamide 12 (PA-U12) has been characterized using standard methods for plastic pressure pipe during the qualification process for use in buried piping systems for natural gas delivery operating at low ambient temperatures, usually less than 20 to 30°C at pressures...
Author(s) : Dr. Michael Pluimer, Sara Stone
The Notched Constant Ligament Stress test (NCLS test, ASTM F2136)[1] is a test method that measures the slow crack growth in High Density Polyethylene. The NCLS test requires a notch on all test specimens to act as a stress concentration at that point so crack propagation can be easily predicted and studied. In...
Author(s) : Ernst van der Stok, Mirko Wenzel, Thomas Kratochvilla, Kurt Engelsing, Werner Weßing, Britta Gerets
It has not been possible to derive an accelerated procedure for the Point Load Test (PLT) as a pipe test before now. Further research and testing were therefore needed to establish appropriate requirements for standards including EN 1555-1 to rule out uncertainty in the market. The PLT is a central product test for...
Author(s) : Sunwoong Choi, Robert Stakenborghs , Pyeongan Lee, Byoungho Choi
This work developed a hydro-axial tension (HAT) test as a whole pipe axial tensile test and applied to evaluate the polyethylene (PE) pipe and fusion joints containing various flaws. HAT test was designed to utilize hydrostatic pressure to cause axial tension in pipes. The experimental and numerical analysis was...
Author(s) : Norbert Jansen
A practical requirement of temperature resistance of minimum 50 years at 70°C was established for the extra high voltage (EHV) corridor projects in Germany. Experts have debated what tests are best suited to prove the suitability of a pipe resin for cable protection pipes which may be installed hastily and under...
Author(s) : Jacob John, Suresh Shenoy, Patrik Roseen
Cross-linked polyethylene (PEX) pipes continue to gain popularity in plumbing and indoor climate applications around the globe. This study focuses on increasing the sustainability of PEX pipes by utilizing recycled PEX and production waste streams into PEX production. Different methods available for recycling and the...
Author(s) : Aisha Khaleel, Suleyman Deveci, Sulistiyanto Nugroho, Fatima AlHameli
The use of polyethylene pipes in transportation networks of pressurized water and gas have shown superb performance over the history. High density, high-molecular-weight, and bi-modal polyethylene materials, known as PE80, PE100 and PE100RC, have successfully served the market for many years in standard applications....
Author(s) : Jessica Hinczica, Mario Messiha, Florian Arbeiter, Gerald Pinter
In Europe, only 1.8 million tons of recycled material is processed in new products within the building and construction sector [1]. Recyclates and blends of recyclates with virgin materials are already used for different products in the plastic pipe industry, such as cable trays, or storm water management...
Author(s) : Mitsuaki TOKIYOSHI, Yutaka SAWADA, Yasuhiko OTSUKI, Kensei INOUE, Takashi KURIYAMA, Toshinori KAWABATA
Polyethylene reinforced with short glass fibres (PE-sGF) pipe, manufactured by combining short fiber glass (sGF) with PE100 as a reinforcing material, has a higher pipe rigidity in the pipe circumferential direction than that of PE100 because of the reinforcing effect of the reinforcing material and a performance...
Author(s) : Kevin White, Shad Sargand
The current standard of practice for the installation of agricultural mains is in accordance with ASTM F449, Standard Practice for Subsurface Installation of Corrugated Polyethylene Pipe for Agricultural Drainage or Water Table Control. ASTM F449 has several limitations. Currently, the allowable maximum height of...
Author(s) : Carine Lacroix, Philippe Louvel, Danielle Mark, Dominique Gueugnaut
A test program was carried out on two Polyamide resins, Polyamide 11 (PA11) and Polyamide 12 (PA12), both certified for gas networks. Polyamide’s advantage lies in its implementation, similar to that of polyethylene, and its properties allowing it to operate at up to 18 bar for gas, all other conditions being equal....
Author(s) : Carlos Domínguez, Predrag Micic, Rafael Juan, Nuria Robledo, Rafael A. García-Muñoz
Slow Crack Growth (SCG) resistance is the main property that must be controlled for assessing the long-term performance on polyethylene resins used for pipe application. The latest generation of bimodal and multimodal ethylene-α-olefin copolymers with exceptional balance of mechanical properties and processability...
Author(s) : Chantz Denowh, Robert Stakenborghs, Liang Yu
The use of spoolable reinforced thermoplastic pipe (RTP) technologies in the onshore oil and gas industry has expanded significantly over the past decade. It is anticipated that interest will only continue to grow as oil and gas operators transition to transporting alternative fuels such as hydrogen and carbon...
Author(s) : Amster Howard
This paper focuses on the confusing plethora of choices that a design engineer in the United States faces when selecting installation instructions for buried pressure thermoplastic pipelines. For polyethylene pipe, the decision is between AWWA Manual M55, ASTM D2774, ASTM F1668, the PPI Handbook, MAB-3, PE Field...
Author(s) : Chris Greggs
Much has been done to improve the quality and efficiency of HDPE pipe installations over the years. Now, a totally new concept for fusion where the machine meets the pipe where it lays to improve worksite safety, boost jobsite efficiency, and minimize the amount of time spent between fusions has been developed. This...
Members of the Association
