Plastic Pipes Conference Association # 2023 Lake Buena Vista
Mitsuaki TOKIYOSHI, Yutaka SAWADA, Yasuhiko OTSUKI, Kensei INOUE, Takashi KURIYAMA, Toshinori KAWABATA
Polyethylene reinforced with short glass fibres (PE-sGF) pipe, manufactured by combining short fiber glass (sGF) with PE100 as a reinforcing material, has a higher pipe rigidity in the pipe circumferential direction than that of PE100 because of the reinforcing effect of the reinforcing material and a performance similar to PE100 in terms of flexibility in the pipe axial direction. This performance is clarified by the numerical value of the tensile yield stress or tensile modulus of elasticity, which can be obtained by tensile tests that use specimens extracted from the PE-sGF pipe in the circumferential or axial direction. However, the factors behind the mechanical behavior remain unclear. Therefore, the orientation of the sGF was confirmed using X-ray CT analysis. The results show that the striped pattern orientation angle mapping results were obtained in the extrusion direction and thickness directions. This striped pattern indicates that the orientation of the sGF is cross-oriented with a slight inclination to the extrusion direction; the orientations switch at an interval of constant thickness. These thicknesses are equivalent to the thickness of each layer of the PE-sGF pipe, similar to the cross-winding molding method. Therefore, the sGF were proven to be oriented according to the extruded manufacturing angle, while the pipe was mostly reinforced in the circumferential direction. Thus, while physical properties and orientation analysis are being clarified, in this study, the focus is on the glass fibers flow during extrusion molding and performance of a flow analysis to see how the sGF orientation was formed in the die.
Related papers
Author(s) : Ajay Taraiya, Peter Degenhart, Mark Boerakker
In PPXX, a technology was presented for the first time that could bi-axially orient polyolefin pipes. With this technology, it is possible to prepare pipes that have a performance far beyond the standard ones. One approach to achieving this performance is via a continuous in-line process. To optimize the in-line...
Author(s) : Olivera Bilic, Vivek Rohatgi, Brody Peterson, David Hukill
Demand for conduit pipe is expected to surge globally due to rapid industrialization and urbanization in residential and commercial sectors. Just in the U.S., according to Market Research analysis, expected growth of the plastic conduit pipe market is at a CAGR of more than 5% over the next ten years. In response to...
Author(s) : Yi Zhong, Qianshi Ma, Haihua Yu
BSTRACT The residential district adopts central heating for low temperature radiators system. Due to the disrepair of the secondary heating pipe network that pipe from heat exchange station to user entrance, the running, leaking, dripping and leakage are serious, and the accidents occur frequently. The heat...
Author(s) : Amster Howard
This paper explores the use of a composite soil stiffness as a valuable design tool to consider when a pipeline traverses through poor soil conditions. Thermoplastic pipe are flexible pipe and require good soil support at the sides of the pipe to minimize deflection. However, sometimes the trench walls are weak soils...
Author(s) : James F. Mason, Akshay Ponda, Hermann van Laak, Tobias Bauer
The long-term strength of unplasticized polyamide 12 (PA-U12) has been characterized using standard methods for plastic pressure pipe during the qualification process for use in buried piping systems for natural gas delivery operating at low ambient temperatures, usually less than 20 to 30°C at pressures...
Author(s) : Sunwoong Choi, Robert Stakenborghs , Pyeongan Lee, Byoungho Choi
This work developed a hydro-axial tension (HAT) test as a whole pipe axial tensile test and applied to evaluate the polyethylene (PE) pipe and fusion joints containing various flaws. HAT test was designed to utilize hydrostatic pressure to cause axial tension in pipes. The experimental and numerical analysis was...
Author(s) : Jacob John, Suresh Shenoy, Patrik Roseen
Cross-linked polyethylene (PEX) pipes continue to gain popularity in plumbing and indoor climate applications around the globe. This study focuses on increasing the sustainability of PEX pipes by utilizing recycled PEX and production waste streams into PEX production. Different methods available for recycling and the...
Author(s) : Aisha Khaleel, Suleyman Deveci, Sulistiyanto Nugroho, Fatima AlHameli
The use of polyethylene pipes in transportation networks of pressurized water and gas have shown superb performance over the history. High density, high-molecular-weight, and bi-modal polyethylene materials, known as PE80, PE100 and PE100RC, have successfully served the market for many years in standard applications....
Author(s) : Kevin White, Shad Sargand
The current standard of practice for the installation of agricultural mains is in accordance with ASTM F449, Standard Practice for Subsurface Installation of Corrugated Polyethylene Pipe for Agricultural Drainage or Water Table Control. ASTM F449 has several limitations. Currently, the allowable maximum height of...
Author(s) : Chantz Denowh, Robert Stakenborghs, Liang Yu
The use of spoolable reinforced thermoplastic pipe (RTP) technologies in the onshore oil and gas industry has expanded significantly over the past decade. It is anticipated that interest will only continue to grow as oil and gas operators transition to transporting alternative fuels such as hydrogen and carbon...
Author(s) : Amster Howard
This paper focuses on the confusing plethora of choices that a design engineer in the United States faces when selecting installation instructions for buried pressure thermoplastic pipelines. For polyethylene pipe, the decision is between AWWA Manual M55, ASTM D2774, ASTM F1668, the PPI Handbook, MAB-3, PE Field...
Author(s) : Chris Greggs
Much has been done to improve the quality and efficiency of HDPE pipe installations over the years. Now, a totally new concept for fusion where the machine meets the pipe where it lays to improve worksite safety, boost jobsite efficiency, and minimize the amount of time spent between fusions has been developed. This...
Author(s) : Peter Youssef, Sultan Alkendi, Hussein Basha
Bahr El-Baqar Water Treatment Plant, produces 2 billion m3 per year, introduces a sustainable solution for environmental pollution recovery and irrigation water source (via recycling the water of Bahr El- Baqar drain); whereas it protects the environment and generates water to support the cultivation of 4000 km2 in...
Author(s) : Chris Ziu, Deanne Hughes, Steve Sandstrum
Plastic pipe is an environmentally responsible choice for a broad array of piping applications. The exceptional chemical/corrosion resistance, superior joining techniques and overall durability of these piping products have resulted in industry-leading life-cycle analyses (LCA’s) in the applications for which they...
Author(s) : Dr. Jan Hendrik Beckmann
For several decades now plastic pipes have been measured in-line [1]. However, currently used technologies also challenge the user in many ways, either by elaborate conversion work on the system for dimensional changes or by frequent calibration procedures [2] or in some cases the use of water as coupling medium [3]....
Author(s) : Norbert Jansen, Andrew Wedgner, Rainer Kloth
PE100+ Association(client) has sponsored a technical investigation to define the permeation rate of hydrogen through polyethylene pipes at an external expert laboratory. Four different types of PE pipe materials in the same pipe size and SDR17 have been evaluated at 3 different target temperatures 8°C, 14°C and 20°C,...
Author(s) : Suleyman Deveci, Aisha Khaleel, Birkan Eryigit
Short and long term hydrostatic pressure resistance of plastic pipes are measured according to ISO 1167, by applying an internal pressure that is calculated for the target hoop stress considering outer diameter and wall thickness of the pipe samples. Due to the nature of the extrusion process, wall thickness...
Author(s) : Kevin White, Shad Sargand
Re-rounding is a technique for remediating excess deflection in corrugated highdensity polyethylene (HDPE) pipe meeting AASHTO M-294 with diameters between 12" and 60" using a pneumatic device vibrating from within the pipe and pushing against the inside crown and inverted to redistribute the surrounding backfill and...
Author(s) : Steven L. Barfuss
In 2022, USU completed the most comprehensive water main break survey ever undertaken in North America to determine the performance of different pipe materials. More than 800 utilities responded to the survey. The survey respondents from this study represent 410,000 miles or 16.7% out of an estimated 2.45 million...
Author(s) : Harry Mavridis
Demand for thick-wall (i.e., greater than about 2”-3” in thickness[15] ) HDPE pressure pipe is increasing worldwide for water, mining and oil & gas gathering applications. Resin producers have been developing HDPE resins that combine performance requirements (PE4710 or PE100) with processability attributes needed for...
Members of the Association
