Plastic Pipes Conference Association # 2021 Amsterdam
M. Eckes & Dr. B. Baudrit, Dr. M. Troughton & D. Wylie, H. van Laak & J. Fritz
Unplasticized polyamide 12 (PA-U12) is increasingly being used in pipe applications, especially in the gas sector. However, the material behavior in the usual quality tests for pipe welds has not yet been thoroughly investigated. For this reason, two research institutes, worked in cooperation with a manufacturer of PA-U12 to examine the established quality tests for pipe welds in PA-U12 pipes. Among the test methods were destructive test methods as well as ultrasonic inspection methods for non-destructive testing of pipe welds. The results provide an insight into the assessment of the quality characteristics of PA-U12 pipe welds and will be used for the training of personnel as well as for the extension of international technical standards.
Related papers
Author(s) : Mike Troughton, Amir Khamsehnezhad, Changyi Yu
When butt fusion welding polyethylene (PE) pipes in the field, it is often specified that the pipes must undergo fusibility testing in all combinations of suppliers, diameters and thicknesses before being fused in production. This is a very onerous and expensive task, but must be carried out to ensure that the PE...
Author(s) : Shuhei Nishida, Shintaro Iwasaki, Hidefumi Yamanaka, Takahiro Kasatani
Polyethylene pipelines have been used for natural gas service applications for over 40 years in Japan. It is thought that they will continue to be used widely for many years. Therefore, it is important to confirm the conditions of the existing pipelines being used for the long term. In this study, polyethylene pipes...
Author(s) : James F. Mason, Akshay Ponda, Hermann van Laak, Buc Slay
The effects of liquid hydrocarbons on long term strength of pipe grade thermoplastic resins is an important consideration when designing pressure pipe for use in the oil and gas industry. There is an extensive body of work going back several decades descri bing these effects for pipe grade polyethylenes, and all...
Author(s) : Sjoerd Jansma, René Hermkens
More than 20,000 km of rigid PVC (or PVC-U) pipes are currently in use for the distribution of natural gas in the Netherlands. In this decade, the majority of these pipes will reach their initially specified lifespan of 50 years. In the light of a possible replacement surge, it is increasingly important to...
Author(s) : Greg Scoby, PE
This paper will detail the steps taken during adoption of HDPE for potable water systems improvements including material justification, creation of related specifications, investigation of available piping components, qualification of contractors and the construction/inspection of related systems. The City of...
Author(s) : Christian Schalich
Plastic pipes for infrastructure and building applications are precisely specified with regards to wall thickness and diameter. Pipe manufacturers use different measuring methods in order to ensure the required dimensional accuracy and maintain a constant high quality. This paper introduces a measuring system based on...
Author(s) : Mario Messiha, Britta Gerets, Jan Heimink, Andreas Frank, Florian Arbeiter, Gerald Pinter
A majority of field failure of viscoelastic plastic pipes can be attributed to slow crack growth (SCG) and has become crucial in terms of characterization of newly developed materials – particularly, if they are designed for pressurized pipe applications. In this study, investigations in terms of SCG resistances...
Author(s) : Suleyman Deveci, Nisha Preschilla, Sulistiyanto Nugroho, Birkan Eryigit
Carbon black (CB) has been used as a perfect and the cheapest solution to prevent photo degradation of polyethylene against UV light exposure. The effect of carbon black on the mechanical properties of polyethylene pipes was studied extensively, but only on well dispersed and distributed carbon black...
Author(s) : Thomas R. Kratochvilla, Patrick Grünbeck, Christoph Bruckner, Raimund Eremiasch, Harald Wilhelm, Mario Vukelja
In the last decades pipe dimensions of extruded PE pipes have reached new orders of size. Today, PE pipes with outer diameters of up to DN/OD 3500 mm are produced and used for pressure pipe applications like seawater intake/discharge, outfall, sewage and industrial process piping systems. To test the long-term...
Author(s) : Kensei INOUE, Mitsuaki TOKIYOSHI, Joji HINOBAYASHI, Takeshi KARINO, Toshinori KAWABATA, Takashi KURIYAMA
As the worldwide problems are over-population, unusual weather like as localized heavy rain and climate change. Against those problem, it has to need new projects to make a new agricultural field, drainage pipeline system and to spread the new underground irrigation system at peat land whereas spots of about 2 million...
Author(s) : Florian Arbeiter, Tobias Schachinger, Stefanie Eichinger, Gisbert Rieß, Michael Stur, Michael Steiner, Florian Saliger
Plastic pipes are of outstanding importance for the distribution of potable and process waters, oil and gas, as well as for sewer and waste water disposal. However, plastic pipes are also used in many other technical areas. Especially in European countries with mountainous regions, such as Austria, Switzerland, Italy...
Author(s) : Justin Brandt, Mike Griffin, Tony Cuvo
As plastic pipe gains share in new markets and applications, additional joining methods add further value, enabling continued growth for plastic pipes. To date, definitions of a “fit-for-purpose” mechanical joint for High Density Polyethylene (HDPE) pressure piping systems can vary significantly. As such, mechanical...
Author(s) : Sjoerd Jansma, Peter Cloos, Ernst van der Stok
This paper describes two different test methods used to determine the permeation rate of hydrogen through a reinforced thermoplastic pipe (RTP) system with a HDPE liner pipe and a gas-tight layer at a pressure of 42 bar(g) hydrogen and ambient temperature. One method involThe results of the aforementioned tests...
Author(s) : Hermann van Laak, Jan Heimink, Mario Messiha, Andreas Frank, Christoph Bruckner, Thomas Kratochvilla
For high pressure pipes above maximum operation pressure of 10 bar, this paper emphasizes PA-U12 as the easy to install alternative to steel. It underlines the superb performance of PA-U12 pipes for alternative installation techniques without need for a separate mechanical protection. An unplasticized polyamide 12...
Author(s) : Jörg Wermelinger, Sunwoong Choi
In the development of an international standard on non-destructive test for polyethylene electrofusion socket (EF) joints, the inspection capability of the phased array ultrasonic test (PAUT) in assessing flaws in the joints was needed to establish procedure qualification of the test method. For this, a worldwide...
Author(s) : Yilaing He, Tianjun Zhang
A new electrofusion PE belt is developed by reinforcing it with various layers of steel mesh. It’s of sandwich structure, consisting of steel mesh reinforcement, heating wire and polyethylene. One or more layers of steel mesh is encapsulated in the middle, and heating wire is embedded onto “inner side” of the belt....
Author(s) : Dominique GUEUGNAUT, Manuel TESSIER, Romuald BOUAFFRE
Given the virtual absence of available up-to-date results regarding the acceptance criteria for defects at electro-welding interfaces, a study has been launched by GRTgaz RICE with the two-fold aim of confirming the accuracy of the PAUT technique for the detection and sizing of calibrated pit-shaped defects implanted...
Author(s) : Markus Gall, Reinhold W. Lang, Joerg Fischer, Ansgar Niehoff, Steven Schmidt
Despite recent efforts in promoting the utilization of recycled polymeric materials for more diverse and more advanced applications, there are still significant knowledge gaps with regards to the applicability of certain recyclate types for specific “re-use” purposes. When it comes to pipe applications, for instance,...
Author(s) : Mario Messiha, Andreas Frank, Isabelle J. Berger, Jan Heimink, Hermann van Laak, Florian Arbeiter, Gerald Pinter
Since the last decade polyamide 12 (PA12) has been successfully introduced as material for SDR 11 gas piping systems up to 18 bar, representing itself as an attractive alternative to steel pipes for high-pressure applications. Practical experience has confirmed that beside the higher strength, PA12 pipe grades ...
Author(s) : Ernest Lever
Six different polyethylene materials were tested using Cyclic Pressure Fatigue (CPF) as the accelerating process to correlate the results to conventional long-term hydrostatic test results that were previously developed as part of the material qualification process. The designation of the materials was unknown to the...
Members of the Association
