Posters
Plastic Pipes Conference Association # 2014 Chicago
Tu Xiangqun, Wang Chao
Two kinds of comprehensions about the wall thickness of socket fusion fittings from GB/T 28799.3- 2012 have been analyzed in this paper. Socket wall thickness relative to the different value of pipe series of fusion fittings was calculated respectively, and two kinds of simplified calculation have been suggested. The conclusions from the suggested formula and the key points of the structure design mentioned in this paper have been fully verified in laboratory testing and practical application. It will be likely to bring the suggested calculation method into the product standard for improving the quality and applied technology of socket fusion fitting.
Nearly 50 years of plastic pipe product development and design, along with advances in production methods and application of connection technology, socket fusion fittings have been wieldy used in China and throughout the world. Socket fusion fitting systems used heat to form a complete hermetically sealed system, which played an important role in the connection, diverting, branch and variable features, depending on the dimension, structure, properties, and molding process of pipe fittings. According to the National Standard of GB/T 28799.3—2012, the wall thickness and structure of socket fusion fittings were studied in the following, which maybe referenced for relevant professional and technical officers.
Related papers
Author(s) : A. Taraiya, P. Degenhart, M. Soliman, M. Boerakker, R. Handstanger, R. Kleppinger
Since the introduction of polyolefins for pressure pipes, continuous improvements have been made to meet ever-higher demands on their performance and to expand their application window beyond their original scope, mostly based on new resin formulations. Today, we also continue to push the limit to provide better...
Author(s) : Drew Mueller, Peter Dyke
HDPE Pipe holds a dominant position in several markets in North America: natural gas distribution, oil patch, mining, landfill and geothermal. So why are polyethylene’s municipal water and wastewater market shares so much lower than these other industries? How has the polyethylene industry been successful in growing...
Author(s) : Derek Muckle
A technical program has been undertaken to provide evidence on the suitability of polyethylene pipe and fitting systems for the distribution of hydrogen fuel gas. The underlying principle has been to evaluate material in the form of a pipe and to consider the performance of the pipe and of the welded jointing systems...
Author(s) : Lei Wang, Guozhi Xu, Qiaoping Qiu, Weihua Lu, Yanwang Han
PP-R (random copolymerized polypropylene) has been widely used in hot and cold water systems. However, the standard PP-R pipes have the disadvantages of a large high-temperature thermal expansion coefficient, an insufficient notched impact strength, and a low temperature and pressure resistance. In this paper, a new...
Author(s) : Ilija Radeljic, Ebbe Smith
HDPE pipe can be relatively easily scratched during the manipulation on the site, which is especially true for the marine pipelines. Installing the scratched marine pipe with the S bend method presents a risk and repair methods are usually performed. Currently, there is no standard defining the repair procedure, in...
Author(s) : Paul J. Freudenthaler, Joerg Fischer, Mathias Eder, Reinhold W. Lang
For controlled water disinfection, typically chlorine is used and preliminary studies demonstrate its aging and crack growth acceleration effects on polyolefin pipe materials [1, 2]. Although the use of recycled plastics is not prohibited in some ISO standards for polyolefin piping systems [3–5], only small amounts...
Author(s) : Mike Troughton, Amir Khamsehnezhad, Changyi Yu
When butt fusion welding polyethylene (PE) pipes in the field, it is often specified that the pipes must undergo fusibility testing in all combinations of suppliers, diameters and thicknesses before being fused in production. This is a very onerous and expensive task, but must be carried out to ensure that the PE...
Author(s) : James F. Mason, Akshay Ponda, Hermann van Laak, Buc Slay
The effects of liquid hydrocarbons on long term strength of pipe grade thermoplastic resins is an important consideration when designing pressure pipe for use in the oil and gas industry. There is an extensive body of work going back several decades descri bing these effects for pipe grade polyethylenes, and all...
Author(s) : Ernst van der Stok
For PE 100-RC, two tests are still under development for pipes: the point load test (PLT) and the accelerated notch pipe test (aNPT). The PLT was developed by a project group consisting of manufacturers and end users. The PLT determines the resistance to point loads as they can occur in practice. An earlier study...
Author(s) : S. Nestelberger, J. Cheng
The Point Load Test (PLT) [ 1, 2] was designed to simulate the SCG (slow crack growth) failure initiated by a rock pressing into the exterior wall of a polymer pipe. Today’s PE materials sustain long PLT testing times, due to its high SCG resistance design. Consequently, an accelerated “PLT+” with the support...
Author(s) : Amster Howard
Flowable fill is used for many applications, but mainly for pipe trench embedment and backfill. There are three ways that using flowable fill can be kind to the environment. Because flowable fill is self-leveling and has a strength greater than the native soil, the trench cross section can be minimized. This means...
Author(s) : Gerald Pinter, Johannes Wiener, Florian Arbeiter, Abhishek Tiwari, Otmar Kolednik
For pipe applications, catastrophic failure due to crack growth has to be prevented by all means. Techniques to develop new and even tougher pipe materials are explored in this contribution. The aim is to create a multi-layer architecture, that exhibits high toughness as well as damage tolerance towards sharp notches....
Author(s) : Prashant Nikhade, Farraj Tashman
In the Middle East and India, PE pipes have expanded their applications in a big way for water supply, industrial effluents, corrosive chemical transportation, slurry transportation, city gas distribution networks and agriculture irrigation purposes over ductile iron, cast iron and other conventional pipes. PE...
Author(s) : Greg Scoby, PE
This paper will detail the steps taken during adoption of HDPE for potable water systems improvements including material justification, creation of related specifications, investigation of available piping components, qualification of contractors and the construction/inspection of related systems. The City of...
Author(s) : Christian Schalich
Plastic pipes for infrastructure and building applications are precisely specified with regards to wall thickness and diameter. Pipe manufacturers use different measuring methods in order to ensure the required dimensional accuracy and maintain a constant high quality. This paper introduces a measuring system based on...
Author(s) : Mitsuaki Tokiyoshi, Yuichi Shibao, Yoshitaka Watanabe, Takeshi Yoshioka, Takashi Oka, Kohei Sasaki
It was common to use those pipelines for Steel in Japan. However Steel pipes have the long standing problems that it has been needed maintenance costs for rust prevention and antifouling property. Therefore it had been carried out the project that large diameter polyethylene pipeline applied for circulating water...
Author(s) : M. Eckes & Dr. B. Baudrit, Dr. M. Troughton & D. Wylie, H. van Laak & J. Fritz
Unplasticized polyamide 12 (PA-U12) is increasingly being used in pipe applications, especially in the gas sector. However, the material behavior in the usual quality tests for pipe welds has not yet been thoroughly investigated. For this reason, two research institutes, worked in cooperation with a manufacturer of...
Author(s) : Eng. Grigorios Vigellis, Eng. Mohamed Hageb
Continuous development and innovation in the production of plastic pipes made by high density polyethylene (HDPE) has enabled the industry to produce much larger diameter systems than ever believed possible. The enablers for production of such large plastic pipes are three main pillars: continuous innovation...
Author(s) : Jennifer Ravereau, Jose Teixeira Pinto, Malena Bernabeu, Jose Alacid, Jean-Philippe Le Goff, Frederic Mohier, Benjamin Rabaud
Drinking water network fittings such as valves are made of brass materials known to be robust over long periods. Due to the gradual inflation metallic raw material costs, composite plastic valves have grown in market share. Uncertainties remain, however, on their long-term reliability. The aim of this work is to...
Author(s) : Suleyman Deveci, Nisha Preschilla, Sulistiyanto Nugroho, Birkan Eryigit
Carbon black (CB) has been used as a perfect and the cheapest solution to prevent photo degradation of polyethylene against UV light exposure. The effect of carbon black on the mechanical properties of polyethylene pipes was studied extensively, but only on well dispersed and distributed carbon black...
Members of the Association
