Plastic Pipes Conference Association # 2021 Amsterdam
Joe Babcanec, P.E., Dan Currence, P.E.
The newly released Drainage Handbook provides complete guidance on corrugated polyolefin pipe. Perhaps the biggest contribution this new handbook makes to the advancement of both HDPE and PP corrugated plastic pipe is the design procedure presented. The design procedure reflects the industry’s recommended practice for using the American Association of State Highway Transportation Officials (AASHTO) Load and Resistance Factor Design (LRFD) Bridge Design Specifications [2] methodology currently utilized for bridge design by Departments of Transportation (DOTs) in the United States. The LRFD procedure utilizes numerous load and resistance factors in the design process to evaluate the performance of buried pipe as various limit states are evaluated. The result is a very comprehensive design analysis with multiple layers of conservativism built into the results. In the drainage handbook, the industry applied the LRFD design methodology that most accurately reflects how corrugated plastic pipe is installed in North America. The companion document to the Structural Design chapter, the Design Guide, walks an engineer through the detailed calculation procedure for two unique pipe design scenarios.
In this paper, key details of the structural design procedure in the drainage handbook will be discussed, and one of the examples from the Design Guide will be presented.
Related papers
Author(s) : Olivera Bilic, Vivek Rohatgi, Brody Peterson, David Hukill
Demand for conduit pipe is expected to surge globally due to rapid industrialization and urbanization in residential and commercial sectors. Just in the U.S., according to Market Research analysis, expected growth of the plastic conduit pipe market is at a CAGR of more than 5% over the next ten years. In response to...
Author(s) : Michael O’Rourke
The required wall thickness for a fully fused HDPE water main subject to an earthquake induced lateral spread is addressed in this paper. The water main is assumed to be buried via cut and cover (i.e., open cut with typical burial depths in the 2 to 15 feet range) procedures and any laterals have small diameters. For...
Author(s) : James F. Mason, Akshay Ponda, Hermann van Laak, Tobias Bauer
The long-term strength of unplasticized polyamide 12 (PA-U12) has been characterized using standard methods for plastic pressure pipe during the qualification process for use in buried piping systems for natural gas delivery operating at low ambient temperatures, usually less than 20 to 30°C at pressures...
Author(s) : Jiyong Park, JaeHyuck Han, YoungGu Kim, Eunjin Park
This study investigates the influence of various parameters on polymer design to determine the slow crack growth. HDPE(High Density Polyethylene) materials with different molecular weight distribution and comonomer content for PE100-RC pipe were investigated with cracked round bar test. The cracked round bar test...
Author(s) : Michael Pluimer, Christian Herrild, Patrick Vibien
With enhanced interest in a circular economy and the potential use of recycled HDPE within HDPE conduit, a research project was undertaken to investigate the necessary technical requirements when using recycled HDPE. High Density Polyethylene (HDPE) conduit is a durable product designed to protect cables...
Author(s) : Kevin White, Shad Sargand
The current standard of practice for the installation of agricultural mains is in accordance with ASTM F449, Standard Practice for Subsurface Installation of Corrugated Polyethylene Pipe for Agricultural Drainage or Water Table Control. ASTM F449 has several limitations. Currently, the allowable maximum height of...
Author(s) : Shane Schuessler, Richard Coombs, Mohamed Hageb, Abdullah Saber, Grigorios Vigellis, Chandra Basavaraju
Bordered by Rwanda and the Democratic Republic of Congo sits Lake Kivu, an African Great Lake formed along the East African Rift. Lake Kivu is one of the world’s deepest freshwater lakes and contains enormous quantities of dissolved carbon dioxide and methane gas held at depths greater than 1100 feet (350 meters)....
Author(s) : Chris Greggs
Much has been done to improve the quality and efficiency of HDPE pipe installations over the years. Now, a totally new concept for fusion where the machine meets the pipe where it lays to improve worksite safety, boost jobsite efficiency, and minimize the amount of time spent between fusions has been developed. This...
Author(s) : Jay Parvez, Richard Nichols
All thermoplastic and thermoset pipes must consider the impacts of cyclic loading on overall performance. Since its first use, PVC pipes have been tested for its resilience to such loading. As testing evolved over time, the method to determine cyclic capacity for gasketed PVC pipes has improved. Previously, the...
Author(s) : Peter Youssef, Sultan Alkendi, Hussein Basha
Bahr El-Baqar Water Treatment Plant, produces 2 billion m3 per year, introduces a sustainable solution for environmental pollution recovery and irrigation water source (via recycling the water of Bahr El- Baqar drain); whereas it protects the environment and generates water to support the cultivation of 4000 km2 in...
Author(s) : Michael Pluimer, PhD, Joseph Babcanec, PE
While corrugated HDPE pipes are still the dominant plastic pipe product in the United States for culvert and storm sewer applications, Corrugated polypropylene pipes have continued to gain market share over the past decade. There are currently several different ASTM and AASHTO standards for these products, including...
Author(s) : Dr. Jan Hendrik Beckmann
For several decades now plastic pipes have been measured in-line [1]. However, currently used technologies also challenge the user in many ways, either by elaborate conversion work on the system for dimensional changes or by frequent calibration procedures [2] or in some cases the use of water as coupling medium [3]....
Author(s) : J. Lahoz
An investigation project was launched in 2020 to clarify the relationships between the processing conditions and the design lifetime of PVC-U 250 pipes. Ca/Zn stabilized pressure pipes were extruded with different processing temperatures and characterized by their DSC B-onset temperature and degree of gelation. Their...
Author(s) : Ludo Debever, Peter Sejersen
The Circular Economy Action Plan is a major building block of Europe’s Green Deal, the European Climate Change strategy. It has far-reaching consequences for the entire EU industrial fabric and its business models. The EU’s transition from a linear to a circular economy aims to reduce on natural resources and pave...
Author(s) : Harry Mavridis
Demand for thick-wall (i.e., greater than about 2”-3” in thickness[15] ) HDPE pressure pipe is increasing worldwide for water, mining and oil & gas gathering applications. Resin producers have been developing HDPE resins that combine performance requirements (PE4710 or PE100) with processability attributes needed for...
Author(s) : Dr. Ricky Selle
Structural behavior of flexible plastic manholes is very different from rigid concrete products. Although this is state-of-the-art knowledge, no international or EN standard exists on structural design of these products. Therefore, traditional soil models and soil pressure coefficients are usually applied if...
Author(s) : Guido Quesada
Spigot bevels (also referred to as chamfers) for plastic pipe joints using elastomeric seals are well-known and often prescribed in standards such as ISO 1452 for PVC-U and 16422 for PVC-O. The most common type of bevel is a simple straight cut at a 15° angle with respect to the pipe axis, leaving approximately 50%...
Author(s) : Riwu Yao, Fengyao Ni, Jinkui Wu, Zhiyong Kong, Jianfeng Shi , Jinyang Zheng
Plastic pipelines have been widely used in various industries, such as gas and oil transmission and nuclear power plants. The safe operation of pipelines is a critical concern in applications, and structural health monitoring methods of plastic pipelines are attracting broad interest in both industry and academia. In...
Author(s) : Guido Quesada, Mark Weih
The Plastic Retainer Ring (PRR) gasket is an old friend of pipe joints, and it is still used among other sealing solutions developed more recently. With origins traced back to the end of the 1960s, it is recognized among the first solutions developed for gasketed plastic pipe joints. It is very likely to have...
Author(s) : Dipl. Ing. Rainer Vießmann
The production of PVC pipes is mainly produced on counter rotating twin screw extruders as the PVC Dryblend material is readily available in powder form. Whereas PVC granules, mainly processed on single screw extruders, play a minor role in pipe production for economic reasons. The design of the extruder screws has a...
Members of the Association
