Our site uses cookies necessary for its proper functioning. To improve your experience, other cookies may be used: you can choose to disable them. This can be changed at any time via the Cookies link at the bottom of the page.


Status and suggestions on the application of non-metallic piping technology in oil field

 

Posters

Plastic Pipes Conference Association # 2012 Barcelona

Zhang Li

Bases on the technical features of high-pressure glass fiber reinforced plastic pipes, steel frame PE complex pipes and flexible composite pipes, together with the application status of the above said pipes in oil field and related technical progress, this article will illustrate the existed questions, as well as our suggestions on non-metallic piping technology in oil field engineering. Key words : Non-metallic piping; Technical progress; ASP compound flooding; technical standard

Please note that the whole article content is available on PPCA website only :

Related papers

2021 Amsterdam : A METHODOLOGY TO DETERMINE CHARPY IMPACT STRENGTH OF NOTHCED SPECIMEN CUT FROM PLASTICS PIPES

Author(s) : Li, Yanjun, Xiang, Aimin, Xu, HaiyunBeijing, Xie, Jianling, Ho, Kinman, Xu, HaiyunBeijing

It is necessary to evaluate the impact resistance of plastics pipes as they have the potential to be damaged by hitting or colliding during storage, transportation and installation. As a well-established test method, the Charpy impact strength of unnotched test pieces cut from thermoplastics pipes is determined...

2021 Amsterdam : RECENT DEVELOPMENT OF CHINA PE WATER PIPE STANDARDIZATION AND ITS INFLUENCE ON THE APPLICATION OF PE100 PRE-COMPOUND

Author(s) : Xinwen Yu, Aimin Xiang, Dongyu Fang, Peck Tze Kang, Jinghui Li

The Chinese PE water pipe market has developed significantly in recent years and particularly over the last 12 months. Against a background of water scarcity and growing urbanization, this evolving market has grown significantly in both size and quality awareness. On the back of past experiences, a fundamental...

2018 Las-Vegas : A new flexible jointing method of plastic (PE) pipes

Author(s) : Yilaing He, Tianjun Zhang

A new electrofusion PE belt is developed by reinforcing it with various layers of steel mesh. It’s of sandwich structure, consisting of steel mesh reinforcement, heating wire and polyethylene. One or more layers of steel mesh is encapsulated in the middle, and heating wire is embedded onto “inner side” of the belt....

2018 Las-Vegas : Development status and technical requirements of composite insulating plastic pipe

Author(s) : HU Fa, LI Yue, GAO Yuanjie, ZHE Dongmei, WEI Ruoqi

This paper expounds the development status of composite insulating pipe in the heating and chemical fields from the aspects of materials, structure and application. Combined with the relevant standards and technical requirements, the performance advantages and the key evaluation methods such as axial shear strength,...

2018 Las-Vegas : New high modulus polypropylene helps the development of large diameter utility tunnel

Author(s) : Dongyu Fang, Mark Yu, Zhang Qingfu

In the present paper we introduced how high modulus polypropylene helps an innovative design of utility tunnel up to 4000mm in diameter. High modulus polypropylene shows high modulus but still maintain reasonable flexibility so that tunnel and surrounding soil could form an integrated system, which means no force is...

2018 Las-Vegas : Polyehthylene/aluminum/polyehthylene composite pipe for fuel gas application

Author(s) : Baiqian Li, Jun Wang, Lixian Zheng, Xiaoyi Peng, Lei Wang, Yu Cui, Guozhi Xu

Polyethylene/Aluminum/Polyethylene (PAP) composite pipe has the advantages of corrosion resistance, limited joints and convenient installation. Nowadays PAP pipes are widely used in indoor gas conveyance. But a number of companies encounter difficulties in installing gas meter in users’ house as well as billing. Some...

2018 Las-Vegas : Study on the resistance to external pressure test methods of plastic inspection chambers

Author(s) : Zhang Wei, Wei Ruoqi, Zhou Minghong, Zhou Mingwei,

This article gives a brief introduction of plastic inspection chambers in China. It focuses on the formulation of China's national standard for plastic inspection chambers and conducts the theoretical analysis and data validation of the key technical metrics in the standard for the following three tests: the...

2016 Berlin : Structural wall multilayer composite PE pipe

Author(s) : Sun Qingjun, Liu Tongxi and Zhang Tianjun

A new composite PE pipe for pressure applications has been developed which combines the following features: polyethylene based, of structural wall, of multiple layers and steel reinforced. Another outstanding feature of this product is that large diameters up to dn2200-2600mm can be made and higher ring stiffness is...

2016 Berlin : The study on long-term resistance to liquid media immersion of adhesive-coated steel tapes applied in metal reinforced polyethylene spiral corrugated pipe for underground sewer

Author(s) : Nan Li

The properties of adhesive-coated steel tapes in metal reinforced polyethylene spiral corrugated pipe (MRPSCP) are very important for the properties of MRPSCP. In the present research, we take 3 years to develop a new technology to fabricate BZ-SH99 adhesive-coated steel tapes, which have better properties than those...

2016 Berlin : Underground engineering stress analysis of plastic inspection chambers

Author(s) : Zhang Wei, Wei Ruoqi, Zhou Minghong, Zhou Mingwei,

This article gives a brief introduction of plastic inspection chambers underground test, analyzes the stress borne by plastic inspection chambers from different angles combined with pressure sensors and strain gauges, sorts out some of the underground test data and analyzes the test data, and finally sums up the...

2014 Chicago : Analysis of Noise in Architectural Water Drainage Systems and the Application of Noise Reduction Technology

Author(s) : Li Yanjun

This article describes the general construction and different types of drainage system, including cast iron pipes and plastic pipes, plastic pipe commonly used are: hard PVC pipe (PVC-U), high density polyethylene pipe (PE-HD), polypropylene tube (PP), engineering plastics acrylonitrile - butadiene - styrene (ABS)...

2014 Chicago : Development of Large Diameter PP-B HM Corrugated Pipe in China

Author(s) : Li Xianmei, Fu Zhimin

Despite the increased activity over the last few years, sewage collection and treatment are still a critical problem in rural China which leads to further pollution of water sources and other environmental concerns. This creates a major market opportunity for cost effective plastic non pressure sewage and drainage...

2014 Chicago : Study on Structural Integrity of Plastic Inspection Chambers

Author(s) : Zhang Wei, Wei Ruoqi, Zhou Minghong, Zhou Mingwei, Lin Baoshu, Xiao Lingli

The plastic inspection chamber is one of the rapidly developing products in the field of drainage in China for the past few years. At present, plastic inspection chamber is mainly made of PP, PE, PVC and so on. The manufacturing technologies include injection molding, rotational molding, mechanical assembly and...

2014 Chicago : The Influence of Additive Levels on PE-Xa Pipe Performance

Author(s) : Zhang SiLiang, Zhang ShuangQuan, Guo XiaoLing, Ren YunHong, Wang MingKe

This article describes the effect of additive, light and high temperature on PE-X pipe’s performance. By additive amount changes, will be have different influence to pipe’s brittleness resistance, bending strength, and aging resistance. As cross-linking agent’s content increasing, bending strength enhanced, but...

2012 Barcelona : Effect of Environmental Temperatures on PE Water Pipe Application

Author(s) : Zhang Zhihao, Zheng Xiaoming

PE pipes have been used for many years in China. However, due to lack for engineering experience, some failure or leakages caused by PE pipe axial shrinkage have occurred in practice. In particular leaks were observed at or near the joints between metal and PE pipes. Suspecting that the cause of the leakage was the...

2012 Barcelona : Production Technology Of Large Caliber Reinforced Polyethylene Pipe

Author(s) : Li Xing

Large Caliber Steel Wire Reinforced Polyethylene pipe is composited from profiled wall HDPE with middle layer steel wire reinforcement, current diameter ranges from 400mm to 3000mm. The pipe combines the high rigidity of the steel wire ,the elasticity and good corrosion resistance of the PE resin, as well as the...

2012 Barcelona : The design, caculation and test of drainage pipe project in Yong Yang east road, Wuqing District Tianjin, China

Author(s) : Li Hongshan

The polyethylene corrugated pipe with ribbed steel reinforcement and spirally wound is a new kind of drainage pipeline. The product with ribbed steel reinforcement and spirally wound in Λ between two polyethylene layers, which is combined with high stiffness, high strength of steel and flexibility, corrosion...

2010 Vancouver : Metal Reinforced Polyethylene Pipes in China

Author(s) : Wei Ruoqi, Li Yu-e

China being the world’s most populous country produces the highest volumes of sewage and waste water and due to rapid increase in industrialization this volume is rising fast. According to the statistics from the National Ministry of Construction, by the end of 2007, the water consumption of the 665 cities in China...

2010 Vancouver : The Test Method of Carbon Black Particle Diameter for PE pipes applying for gas

Author(s) : Li Yu-e, Wu Zhijun, Hua Ye, Sun Jiawen

As the polyethylene pipes widely used in the gas fields, their long-term life is demanded more and more strict. The technical requirement about carbon black particle size was defined in the revised ISO 4437 :2007 as one of requirements of material. We can see that carbon black particle size of the compound is an...

2008 Budapest : Characterizing Long-Term Performance of Plastic Piping Materials in Potable Water Applications

Author(s) : Chung, Li, Oliphant, Vibien, Rozental-Evesque, Rabaud

Plastic piping materials confer many advantages for applications in Potable Water transportation. Considerable research has been conducted to develop methodologies for ensuring performance in these applications for service lifetimes that target an excess of 100 years. A key component of these accelerated methodologies...

Members of the Association

BOREALISBOROUGEFormosa Plastics CorporationHanwha TotalEnergiesINEOS O&PIRPCKorea Petrochemical IND. Co., LTD (KPIC)LyondellBasellORLEN UnipetrolPetroChina Dushanzi Petrochemical CompanyPRIME POLYMERSABICSCG Chemicals & Thai PolyethyleneSinopecTASNEE